AboutPrivacy-policyTerms-conditionsFaqContact

    RC Filter Voltage Divider Calculator | RC filter frequency calculator | Capacitor RC circuit calculator

    Created by Md jony islam

    RC Filter Voltage Divider circuit Calculator

    An RC filter is a circuit consisting of a resistor and capacitor connected in series or parallel. It is widely used to filter out unwanted frequencies or shape signal responses in analog circuits. This calculator is an essential tool for anyone designing circuits that require precise filtering or signal shaping.

    Voltage divider RC filter

    RC filter frequency calculator

    View

    Download

    RC voltage divider1 µFRPower Supply+-Vin© Online Works ToolsVoutC1000 Ω8.47 V10 V
    Fig-1: RC voltage divider Circuit
    V
    • nanoVolts (nV)
    • microVolts (µV)
    • milliVolts (mV)
    • Volts (V)
    • kilovolts (kV)
    • megavolts (MV)
    Hz
    • Hertz (Hz)
    • Kilohertz (kHz)
    • megahertz (MHz)
    • gigahertz (GHz)
    • terahertz (THz)
    • revolutions per minute (RPM)
    Ω
    • millohms (mΩ)
    • ohms (Ω)
    • Kiloohms (KΩ)
    • Megaohms (MΩ)
    • Gigaohms (GΩ)
    µF
    • Farads (F)
    • millifarads (mF)
    • microfarads (µF)
    • nanofarads (nF)
    • Picofarads (PF)
    V
    • Picovolts (pV)
    • nanovolts (nV)
    • microvolts (µV)
    • millivolts (mV)
    • Volts (V)
    • Kilovolts (KV)
    • megavolts (MV)

    Learn how we tools this below

    Add this tools to your site

    Buy me a for Source Code

    What Is an RC Filter?

    An RC filter is a combination of a resistor and capacitor connected either in series or in parallel. Usually it is applied in order to attenuate undesired frequencies or define signal response in analog circuits.

    RC filter voltage divider Calculator
    Fig-1: RC filter voltage divider Calculator

    🙋 Try our Electrical Voltage Sum Tool . If you want to learn more about conversions using Electronic Engineering Project Calculators.

    RC Filter Voltage Divider Calculator: Design High-Performance Filters:

    RC filters are one of the simplest yet most important parts of the electronic design if not the most important for filtering and conditioning signals. With our RC Filter Voltage Divider Calculator, individuals can more easily design both low-pass and high-pass filters because it provides voltage ratios and cutoff frequencies. Therefore, I recommended this tool to everyone, including electronics lovers, student, and PE pedantic engineers to use this tool to design and analyse filters.

    Voltage divider RC filter Vout:

    Vout = Vin2𝜋fJRC + 1

    For Example, Input voltage Vin: 10V, Resistor R: 1000 Ω, Capacitor C: 1 µF or, (0.000001 F), Frequency F: 500Hz Vout

    Vout = 10(2 × 𝜋 × 500 × J × 1000 × 0.000001) + 1 or, Vout = 2.41V

    Suggested Reading

    Features of the Calculator

    Supports the input of resistance and the capacitance values in any units such as ohms, kilohms, microfarads, etc. Suitable for use in a wide frequency band covering the audio and radio frequency spectrum. Contributes both voltage ratio and cutoff frequency outputs.

    RC Filters Conversion application

    Frequently Asked Questions - RC filter Conversion FAQs:

    What is an RC filter?

    An RC filter is a circuit that uses resistors and capacitors to filter signals based on frequency.

    Can this calculator be used for AC and DC circuits?

    It is primarily designed for AC circuits, as capacitors block DC signals.

    What is the cutoff frequency in an RC filter?

    The frequency at which the output voltage is reduced to 70.7% of the input voltage.

    What happens if I swap the resistor and capacitor?

    The filter type changes. A resistor followed by a capacitor creates a low-pass filter, while the reverse creates a high-pass filter.

    Is this calculator suitable for high-frequency circuits?

    Yes, it supports calculations for high-frequency circuits, such as RF filters.

    You may like these posts

    About the Author

    Md Jony Islam

    Md Jony Islam: Multidisciplinary Engineer & Financial Expert:

    Md. Jony Islam is a highly skilled professional with expertise in electronics, electrical, mechanical, and civil engineering, as well as finance. Specializing in transformer service and maintenance for 33/11kV substations, he ensures reliable and efficient electrical systems. His mechanical engineering skills drive innovative designs, while his financial acumen supports effective project budgeting. With a strong foundation in civil engineering, he contributes to robust infrastructure development. Md. Jony Islam's multidisciplinary approach ensures efficiency, quality, and reliability across all projects.